How To Install Parking Camera Wires

Download Article

Download Article

A rear-view camera, also known as a backup camera, lets you see what's behind your vehicle without having to look backwards. Though the device comes standard with many new car models, yous can add a rear-view photographic camera to your vehicle if it didn't come with one.

1. 1

   Buy a mountable backup camera for your specific vehicle. For safety, make sure y'all purchase a device specifically designed to exist a rear-view photographic camera. Purchasing 1 fabricated for your specific vehicle volition brand it easier to install than a standard aftermarket camera. So you tin can install it easily, look for a camera that mounts onto or directly behind your license plate.^[1]

   • Look for backup cameras at consumer electronics stores.

2. 2

   Get an external monitor if you want to keep your existing rear-view mirror. An external backup monitor is a small-scale video screen that mounts onto your windshield similarly to a GPS. Though they take upwards more space than internal monitors, external monitors are far easier to see and can be easily replaced if necessary.

   • If you'd like, you tin apply a standard video monitor instead. However, keep in mind that information technology may non have all the same features as devices designed for use with backup cameras.

   Advert

3. 3

   Purchase an internal monitor for a less obtrusive device. An internal fill-in monitor is a fully functioning rear-view mirror that houses a small screen within the glass. Some internal monitors prune on height of your current rear-view mirror, just others replace your original mirror entirely.^[2]

   • Most internal monitors close off and disappear when not in employ, making them a perfect option if you lot desire to preserve your car'due south looks.

4. 4

   Purchase power and video cords if your camera and monitor didn't include them. For most rear-view camera installations, yous'll need camera and monitor splitter cords with connectors for video and power cables, 2 bare wire power cables, and an RCA video cable.^[iii]

   • Most installation kits include these cables, merely some may crave you to buy them separately.
   • Some camera models use wireless transmitters instead of standard video cables.

Advertisement

1. 1

   Take off your rear license plate. Using a Phillips caput screwdriver, remove each of the screws holding your rear license plate in place. And so, pull the plate off and set it aside.^[4]

   • Make sure you lot place the screws in a safe identify then you don't lose them.

2. ii

   Remove your trunk's interior panel. Popular open your trunk and look for a solid interior panel covering the opposite side of your license plate mounting area. Then, insert a trim removal tool or other thin device behind the console and pry information technology off.^[five]

   • Removing this console will expose the car'southward rear wiring chambers.

3. 3

   Drill a small hole in the license plate mounting area. Make sure there are no obstructions between the license plate mount and the rear wiring chamber. Then, create a small hole in the machine using a power drill equipped with a high-speed twist drill bit. Line up your hole so it is direct backside where your photographic camera'southward power and video cable will go.^{[half dozen]}

   • To figure out where to brand the hole, concord your camera up to the area you intend to mount it. Then, notation the spot where its splitting cord sits.
   • Create a hole that's big plenty to fit your camera'south ability and video cablevision.
   • If you come across any obstructions, try to remove them. If you can't, see if you lot can make a hole nearby.
   • For most jobs, you'll need a drill flake that has a diameter betwixt ^one⁄₈ and ¹⁄₄  in (0.32 and 0.64 cm).

4. 4

   Place a safety grommet around your photographic camera cable. Before running your photographic camera cable into the machine, slip a rubber grommet onto it near the non-splitting end. These small rubber washers, available at nearly habitation improvement stores, will keep the wire in place and prevent leaks.^[7]

   • Choose a grommet that'southward just large enough to fit inside the drilled hole.

5. 5

   Run the camera cable into your trunk. Pull the splitting stop of your camera's video and power cable through the drilled hole into the trunk of your motorcar. Make sure you pull information technology tight and so the safety grommet lodges into the drilled pigsty.

   • Your photographic camera cable should run from the outside of the car to the inside of the motorcar.

6. vi

   Locate your car'southward 2 reverse light wires. Reverse low-cal wires are the cords that connect your car'due south tail lights to the dashboard. They hook directly into your vehicle's tail lights and are normally located in the hatch or trunk of your motorcar.

   • These cords look different for every vehicle then, if you lot can't discover them, consult your owner's manual for model specific data.

7. 7

   Strip and separate your auto's reverse light wires. Using a wire stripper or pliers, peel back the safe covering the wires. Then, use a screwdriver or other thin tool to poke a hole through the centre of each exposed wire, separating the individual wire strands.^[8]

   • For safety, make sure you do this while the car is turned off.

8. 8

   Fuse your camera wires with the reverse light wires. Attach one of your bare wire cables to the camera string's ability connector. Then, poke your bare wires through the eye of the exposed reverse light wires and twist them together. For safety, make sure you wrap the combined wires in electrical tape.^[9]

   • Make sure y'all poke your positive (ordinarily red) blank wire through the positive opposite light wire and the negative (usually black) bare wire through the negative reverse light wire.

Advertisement

1. one

   Route your camera's video cable to the front end of the car. Connect your RCA cable to the camera string'due south video connector if necessary. And then, run it through your vehicle to the surface area by the fuse box. Depending on your vehicle model, you lot'll usually exist able to practise this past peeling back the automobile's headliner or side panels and pulling your cablevision through the exposed sleeping accommodation.^[ten]

   • For certain trucks, you may demand to run the video cable through the vehicle's frame rail.
   • In about cars, y'all'll find the fuse box underneath the steering wheel.

2. 2

   Fix external monitors to the front end windshield. If you're installing an external monitor, first attach your device's included mount to the windshield by following the manufacturer'south included instructions. And then, claw your monitor onto the mount.

   • Well-nigh external monitors use a suction mount, though others may come up with a more than complex mounting system.

3. 3

   Adhere internal monitors to the rear-view mirror or mirror mountain. For certain internal monitors, you lot'll need to clip the new device onto your current rear-view mirror. For others, you'll need to take off the mirror and slide your monitor into the pre-existing mirror mountain.^[11]

   • Some internal monitors may come with their ain mounting organization that you'll have to attach to the machine'due south front windshield.

4. 4

   Run the monitor'southward splitter cable to the fuse box. If necessary, hook your monitor's power and video cablevision into the device. Then, route the cable from the monitor to the area next to the fuse box.^[12]

   • If you'd like, utilize a trim removal tool to pop out the headlining panel directly above your windshield. And then, run your cable through the exposed chamber.

5. 5

   Connect your monitor's camera cablevision to the RCA cable. Afterward routing your monitor'south splitter cable, connect the video terminate of the cable to your camera'southward RCA cord. And so, wrap the connected cords with electrical tape to hold them together.

   • If your RCA and video cables have the same ends, you may need to purchase an RCA male to female converter cord. Y'all tin can notice these at most electronic stores.

6. six

   Attach your monitor'southward power cable to a fuse tap. Connect your remaining bare wire cable to the backup monitor's power cord. So, push the positive (commonly ruby) end of the blank wire cable into the open up end of a fuse tap. Finally, crimp the 2 cables together with a pair of pliers.^[xiii]

   • A fuse tap is a small cable that converts a blank wire into a fuse signal. You tin find them at near auto part stores.
   • If you'd prefer, you can leave the bare wire cable off and connect your camera's power cable to a cigarette lighter adaptor. Then, plug this adaptor into your auto'southward cigarette lighter receptacle for ability.

7. 7

   Plug the fuse tap into the fuse box. Locate your fuse box and open it up. Then, plug your fuse tap into an open fuse prison cell. If necessary, check your fuse box's hat or your vehicle's pedagogy manual to run into which slots are open.^[xiv]

   • Later on attaching your fuse, consider taping all your wires together using electrical record to get them out of the way.

Advertisement

1. 1

   Connect your backup photographic camera to its power and video cable. Return to the back of your car one time you've installed the rear-view monitor and all the necessary camera cords. Close the body if necessary, and then connect the fill-in camera to its power and video cable.

   • Your camera's power and video cable should be sticking out of the hole you drilled in the license plate mounting expanse.

2. 2

   Mount the camera to your license plate. If the camera attaches to the front of your license plate, ready it to the plate by following the manufacturer'due south included instructions. If the camera attaches to the back of your license plate, line the device upward with the plate'due south fastener holes and thread screws through them.^[15]

   • In almost cases, yous can attach a rear-view photographic camera to the back of your license plate using the screws you removed from the car earlier.

3. 3

   Reattach your license plate and trim panels. Using a Phillips head screwdriver, put your rear license plate back on your vehicle. Once you've reattached it, give the license plate and fill-in camera house tugs to brand sure they're secure.

   • If yous oasis't already, reattach your automobile'due south interior trunk console and other trim panels by pressing them back onto the vehicle.

4. iv

   Test the photographic camera to make sure everything works. Before using your new camera on public roads, test it in a safe area like your driveway. If it turns on, place a large, durable object like a trash can behind the camera to run across how distorted the image is. If it does non turn on, read your installation manual for troubleshooting information.

   • In many cases, rear-view camera malfunctions are caused by loose or improperly connected wires.

Advertisement

Add New Question

• Question

  I hooked the camera upward and information technology simply flickers. Whatever advice?

  

  Y'all may want to ensure all cables and connections are secured tightly. Double bank check that all connections are correct. If this doesn't work, cheque to see if the camera chosen is in good shape and isn't physically damaged.

• Question

  Suzuki installed reverse parking photographic camera in my Swift Dzire Zxi. But the camera shows upper view and not the ground below. What can I exercise ?

  

  Brand certain that the photographic camera is installed the right manner (not upside down), and bank check the position of the photographic camera mounted. Take it back to the dealer that installed it and inquire them to check the alignment and fit.

• Question

  What is the best height for a reversing camera?

  

  At that place is no optimal superlative for a dorsum-up camera. The ideal tiptop is based off the specific car or vehicle that you take and your personal preferences, along with its intended application. Some back-up cameras are placed on big service trucks so that they can line up to trailer hitches easier, some are to prevent a blindspot on the road. Depending on your awarding, information technology can be placed at any height. Most reversing cameras are a "wide view" style and the specific height location does not always affect the fashion it functions.

• Question

  Then if I hooked up all the wires correctly but even so no power, is information technology a fuse tap that I need to splice into the wires for it to piece of work correctly?

  

  Shannon Phillips

  Community Reply

  Check your world or ground it may exist bad. Utilise your multimeter to see if the footing is okay.

• Question

  Is it still okay to connect the back-upwards camera to the reverse low-cal with cars that take auto lighting? Or, would I need to connect to the reverse wire on the gearbox?

  

  Shannon Phillips

  Community Reply

  Yes, that will be fine, that how it is supposed to exist done. Look for an automobile electrician if you need someone to call.

Inquire a Question

200 characters left

Include your email accost to become a message when this question is answered.

Submit

Advert

• Though well-nigh car dealers and mechanics will not install aftermarket backup camera systems, many sound and electronic shops volition.

Advertisement

• Make sure y'all turn the car off before working with bare or stripped wires. If you need to impact exposed wires while the car is on, put on a pair of shock-resistant rubber gloves.

Advertisement

Things You'll Need

• Rear-view photographic camera
• Rear-view monitor
• Connector cables
• Phillips caput screwdriver
• Trim removal tool
• Power drill with loftier-speed twist chip
• Prophylactic grommet
• Wire stripper or pliers
• Electrical tape
• Fuse tap

Almost This Commodity

Article Summary X

To successfully install a rear-view camera, first remove your vehicle'south rear license plate and interior trunk panel. Using a ability drill, punch a modest hole through the exposed license plate mounting area and run your camera'south power and video cord through it. Attach a bare wire power cable to your photographic camera'southward ability connector, and then strip your car'due south reverse low-cal wires and splice them with your bare wire power cable. To learn how to mountain the rear-view photographic camera and backup monitor, scroll down!

Did this summary aid y'all?

Cheers to all authors for creating a page that has been read 253,826 times.

Did this article help you?

Source: https://www.wikihow.com/Install-a-Rear-View-Camera

Posted by: quachthismillond1969.blogspot.com

Share this post