3d Design Size Of Supports

Supports in 3D Printing: A technology overview

Learn what a 3D printed support structure is, when support is needed and how support might affect the quality and price of your print.

Supports in FDM

Fused Deposition Modeling (FDM) extrudes a melted filament onto a build surface along a predetermined path. As the material is extruded, it cools, forming a solid surface providing the foundation for the next layer of material to be built upon. This is repeated layer by layer until the object is completed.

When is support needed in FDM?

With FDM printing, each layer is printed as a set of heated filament threads which adhere to the threads below and around it. Each thread is printed slightly offset from its previous layer. This allows a model to be built up to angles of 45°, allowing prints to expand beyond its previous layer's width.

When a feature is printed with an overhang beyond 45°, it can sag and requires support material beneath it to hold it up. More information on overhangs and FDM can be found here.

Depending on the degree of overhang, your FDM print might need support

Bridging vs support

There is an exception to this rule:

Hot material can be stretched short distances between two points in a method known as bridging. Bridging allows material to be printed without support and with minimal sag. If a bridge is over 5 mm long, generally, support is required to give an accurate surface finish.

More information on bridging and FDM can be found here.

The ABCs (or YHTs) of FDM support

Consider the letters Y, H, and T, and a set of associated 3D models.

The arms of a model of the letter Y can be printed easily. Even though the arms the of Y are outstretched, because they extend at 45 degrees or less, they do not require support.
The letter H is a little more complicated but if the center bridge is under 5mm, it can be printed without support or any sagging. Over 5mm and support will be required. For this example, the center bridge is over 5mm and support is needed.
The letter T requires support for the arms of the letter. There is nothing for the outer arms to be printed on and the material will just fall down without support.

The image below illustrates YHT with the support material shown in light gray.

A visual illustration of support structures needed for printing a Y, H & T with FDM.

Here is how the YHTs look when printed. The image below now shows the result of the T printed without support. The surface has significant sagging and will require a large amount of post-processing to clean up.

Y, H, and T printed with FDM with support

The letter T fails when printed with FDM without any support structure

The downside of FDM support material

One of the limitations of using support in FDM printing is that post-processing is always required, resulting in marks or damage to the surface in contact with the support.

Another issue is that layers printed upon support will be less perfect as the support will be slightly less stationary than the solid layers.

Support can also be difficult to remove from small, intricate features without breaking the model.

Furthermore, support requires additional printing material and therefore incurs additional costs. The support also needs removal, creating more work for the 3D printing service provider which can also increase the total cost of the print job.

Puzzle piece with support removed showing surface roughness.

How much support is needed for my FDM print?

The arch example below requires only a limited amount of support placed in the correct location to allow it to be printed accurately.

The St. Louis Gateway Arch shows the perfect example of using support with an arch shaped object.

The "Ball in a Cube" shown below is an example that requires a large amount of support.

Removal of the support in this example is complex and involves removing each support element with needle-nose pliers while attempting to limit the damage to the surfaces surrounding the support. Sanding or smoothing the surface after removal of the support is also very difficult.

Without support material this model can simply not be printed in FDM without compromising on quality and accuracy. In this case - despite the added cost and print time - the additional support material used is essential to being able to complete the print.

Close up of -Ball in a Cube- print showing the support structure needed.

Two types of FDM support

FDM printing methods utilize two types of support:

The first, a sort of flat accordion, or lattice, is the most common and is best suited for most FDM prints.
The other type is a 'tree-like' support and is preferred by some printers. This method of support is less popular, however it has less contact with the print surface which can result in a better surface finish post processing.

The printer operator will generally specify the type of support that best suits your application and thus minimizes the aesthetic impact on your design.

Curious about the cost and material options for FDM?

Get instant quote See all FDM materials

Two different types of support structures: Accordion support (left) and tree support (right).

Dissolvable support

On finely tuned printers with two print heads, the support material can be printed with a dissolvable material that does not tear away from the part but instead dissolves away in a chemical solution that does not affect the main material of the printed model.

This will result in a better surface finish where the support is in contact with the main material but can be an expensive and a time-consuming solution.

An example of this is the Ultimaker 3 machine, which utilizes support printed in PVA that is easily dissolved post print. All industrial FDM machines use disolvable support.

SLA & DLP support structures

Stereolithography (SLA) and Digital Light Processing (DLP) create 3D printed objects from a liquid (photopolymer) resin by using a light source to solidify the liquid material.

Depending on the exact printer type, this means that the model is either pulled out of a vat containing liquid material as it is solidified by a light source through a translucent window at the bottom (bottom-up), or it is submerged into the liquid as the top layer is treated by a light source from the top (top-down).

SLA printing process

When is support needed in SLA & DLP?

To make sure that the prints adhere to the print platform and do not float around in the vat, SLA and DLP printers require the use of supports in almost all cases.

Support structures from these printers look like thin ribs, with only small tips actually touching the model to save material and printing time. The number of supports, their location, where they touch the model and the structure is calculated by the software and is dependent on the shape, orientation and weight of the part being printed.

SLA and DLP are some of the most accurate technologies, capable of printing even the smallest and most intricate objects with accurate detail. With proper post-processing, the usage of supports does not impact the quality of the print.

Removing support material from SLA & DLP prints

First, Isopropyl Alcohol (IPA) is used to wash liquid resin off your completed parts. Support structures can be either broken off the surface of the model or removed using pliers. The spots where the support was in contact with the object are then sanded to remove any remaining marks.

Removing support structures from an SLA print

Design Considerations for supports in SLA & DLP

Part orientation plays a crucial role on where support is located for SLA and DLP printing. By reorienting a part, the amount of support (and therefore the cost of the print) can be drastically reduced.

Orientation also plays an important role in where support will be located. If the aesthetic appearance of a surface on a component is paramount, orientating the part so that there is little to no support in contact with that area can also be an option.

For complex prints with a high amount of detail and many thin or intricate features dividing up the print into separate sections and then assembling them together (via snap-fit connections, interlocking parts or adhesives) can also improve print quality and appearance.

Curious about the cost and the available material options of SLA/DLP?

Get instant quote See all SLA materials

SLA printed part showing some marks where support was located

Material Jetting support structures

Material Jetting (Stratasys PolyJet and 3D Systems MultiJet Modeling) technologies are similar to inkjet printing, but instead of jetting drops of ink onto paper, these 3D printers jet layers of liquid photopolymer onto a build tray and cure them instantly using UV light.

When is support needed in Material Jetting?

These printers require the use of support material in all cases where there are overhanging parts, regardless of the angle. Supports are either water-soluble or are removed during post-processing using plyers, water jetting, ultrasonic bath and sandblasting.

Unlike FDM, supports for these technologies are in no way detrimental to the looks, surface quality or technical properties of the prints. After proper post-processing, it's practically impossible to distinguish parts that were covered with support from the rest of the print.

Removing water soluble support material from a PolyJet print

Design Considerations for supports in Material Jetting

Due to the power tools (waterjet, sandblaster) used during-post processing, intricate parts of the model might get damaged or bent. Make sure to follow Material Jetting rules to avoid any issues. If your model has intricate parts and thin wires, SLS printing is recommended instead.

More resources for engineers

SLA 3D printing materials compared

Compare the main SLA 3D printing resins - standard, tough, durable, heat resistant, rubber-like, dental and castable - by material properties and find the best option for your application.

Read article

Introduction to binder jetting 3D printing

In this introduction to Binder Jetting 3D printing, we cover the basic principles of the technology. After reading this article you will understand the fundamental mechanics of the Binder Jetting process and how these relate to its benefits and limitations.

Read article

Selecting the right 3D printing process

Decision making tools and generalized guidelines to aid you select the right 3D printing process for your application.

Read article

Introduction to metal 3D printing

In this introduction to metal 3D printing, we cover the basic principles of SLM and DMLS. Learn the fundamental mechanics of SLM and DMLS and how these relate to the key benefits and limitations of 3D printing.

Read article

HP MJF vs. SLS: A 3D printing technology comparison

In this article we compare critically HP's Multi Jet Fusion (MJF) with Selective Laser Sintering (SLS) in terms of accuracy, materials, cost and lead time. We cover the current state-of-the-art to help you choose the right technology for your application.

Read article

Introduction to material jetting 3D printing

In this introduction to Material Jetting 3D printing, we cover the basic principles of the technology. After reading this article you will understand the fundamental mechanics of the Material Jetting process and how these relate to its benefits and limitations.

Read article

3D printed injection molds: Materials compared

We compare critically two industrial 3D printing materials used for low-run injection mold manufacturing.

Read article

What is SLS 3D printing?

Learn about the basic principles of selective laser sintering, also known as SLS 3D printing. Discover how SLS 3D printing works, the advantages of SLS techniques for rapid prototyping and low-production runs, and the various materials and options available that will suit your part or project.

Read article

What is SLA 3D printing?

Get to know the basics of stereolithography, also known as SLA 3D printing. Find out why the original 3D printing technique is still so popular and cost-effective, learn about how SLA printing works and its parameters, and discover which materials and options will best suit your 3D-printed part or project.

Read article

What is FDM 3D printing?

Get to know the basics of Fused Deposition Modeling, also known as FDM 3D printing. Learn why this 3D printing technique is so affordable, and why it is an excellent choice for quick, low-cost prototyping. Delve into FDM materials and the advantages and disadvantages for designers and engineers alike.

Read article

Industrial SLA/DLP vs. desktop SLA/DLP

SLA/DLP technology is used by both low-cost desktop 3D printers as well as high-end industrial 3D printers. This article will help you select the right type of machine for your application.

Read article